Auto Car Cooling System Aluminum Radiator for Volkswagen

Auto Car Cooling System Aluminum Radiator for Volkswagen

                      Micro channel parallel flow radiator professional company

The condenser-a part of the air conditioning circuit-is built-in into the engine cooling module, exactly where it is utilized to great down and condense the compressed, gaseous refrigerant from the compressor. We make brazed, flat tube condensers that deliver substantial overall performance in spite of their compact and light-weight design. They ensure fast cooling of the passenger compartment thanks to the best possible matching of warmth transfer and stress fall on the two the coolant and the air aspect.

The condenser is a warmth exchanger in a cellular A/C system. Presently, condensers are normally created of aluminum, but in the previous, some had been produced of copper/brass. Condensers search extremely considerably like radiators, just a small thinner, and given that they also depend on air flowing by way of them, are usually found in entrance of the radiator.
Like radiators and evaporators, condensers are also built as a sequence of tubes with fins all around them. its  job is to release warmth. More especially, to release the heat the refrigerant absorbed even though it was flowing via the evaporator, extremely significantly the same way the radiator releases the warmth from engine coolant that the coolant absorbed although it was flowing via the motor. The refrigerant enters the condenser as a higher-force vapor, but as it flows by means of the condenser and cools, it turns again into a cooler large-strain liquid.

Solution features
1 adopt low height fins and multiple flat pipes to increase the heat dissipation area and improve the heat dissipation performance.
2 fin special treatment to enhance lodging resistance and maintain the tidiness of the products’ appearance 
3 powder coating on the products can enhance corrosion resistance and improve product life cycle.
4 none- argon arc welding solder products look different.
5 every product’s pressure is maintained by using nitrogen so the product is free from leakage at 100% before it leaves the factory

Company Advantage
one. Generic products are supposed to be manufactured strictly according to the installation standard of the original factory, in this way to ensure the accurate installation for the users.
two. This special design for the pin not only enhances its lodging resistance,ensure the visual appearance tidy but also reduces the air blockage chance, it also allows more heat dissipation area to improve heat transfer performance. In that way, the air conditioning system can achieve its expected function more efficiently.
3. Part of the products uses galvanised microchannel flat tube as material or adopt the powder coating treatment, in order to improve products’ corrosion resistance and prolong the service life.
four. By machining core into different thickness and wave distance and changing the amount of holes in flat tube,we can improve the heat dissipation efficiency of condenser of the product, lower down the system compression power, save fuel and improve economic efficiency.
five.CZPTy product is double checked and a pressure-holding device is installed to ensure that every product is 100% leak-free before it leaves the factory.
six. The company with a complete production chain, is focused on the developing new products, and keeping tracking of products to ensure the timeliness of all product supply, and also enhance the flexibility of enterprise operation.
seven.Only when we have an independent team with high efficiency can we satisfy CZPT demands.  

Lengthy phrase organization is dependent on our reliable companies, fast respond and our expert experience to Automobile AC. We’ll turn out to be your associate, not just your supplier.
1.CAD Drawing, and mould design foundation on your sample
two.Mould examination and sample verification ahead of mass production.
three.CZPTers of various transport lines.
4.competitive freight offers and one particular-quit service on clearing, shipping problems.

Q1. Are you a factory or investing firm? A: we’re a self -personal manufacturing unit, we provide 1-stop provider for our clients, from spare components to condenser, from technical product sales to transport and to after-revenue, so as to preserve the cost for client, handle the good quality and direct time, offer the greatest providers
Q2: In which is your manufacturing unit located? How can I pay a visit to there? A: Our manufacturing unit is located in  HangCZPT, Shan dong, China.
The closest airport is ZheJiang Yaoqiang airport or HangCZPT Liuting airport.
Q3. What is actually the manufacturing time for new molds and mass creation? A: 7-10 days to build the new moulds, mass generation normally takes close to 20-25days for one 20gp,twenty five-30days for 1 40hq, can process urgently if need.
This autumn: What is the payment phrases? A: Telegraphic Transfer (T/T) and Letter of Credit score (L/C).
Q5: Can you ship me samples? A: Sure, Samples are for free, and freight is on your facet.


Auto Car Cooling System Aluminum Radiator for Volkswagen


leaf chains

As one of leading leaf chains manufacturers, suppliers and exporters of mechanical products, We offer leaf chains and many other products.

Please contact us for details.

Mail:[email protected]

Manufacturer supplier exporter of leaf chains.

Recent Posts